The Tektronix TDP1000, TDP0500, and P6251 are high-voltage differential probes that deliver the high-speed electrical and mechanical performance required for switch-mode power supply (SMPS), CAN/LIN bus, and high-speed digital system designs. Each probe connects directly to compatible Tektronix oscilloscopes and resolves differential signals with measurement fidelity by combining outstanding electrical performance, versatile device-under-test connectivity, and ease of use.

A differential probe measures the voltage between two points in a circuit, neither of which need be at ground potential — essential for the floating and high-side measurements common in power electronics. These probes are applied to high-speed switch-mode power supply design, CAN/LIN bus design, digital design and characterization, manufacturing engineering test, and research and development.

ValueTronics stocks test and measurement equipment in its own 20,000 sq ft secure warehouse at 1675 Cambridge Drive in Elgin, Illinois. Every pre-owned probe we sell is inspected and functionally verified in-house by our technicians before it ships, while new units ship factory-sealed exactly as received from the manufacturer.

Brand Heritage

Tektronix, founded in 1946, operated as an independent test and measurement company for decades before being acquired by Danaher Corporation in 2007. Since Fortive Corporation's 2016 spinoff from Danaher, Tektronix has operated as part of Fortive.

Compare Other Models in This Series

The TDP1000, TDP0500, and P6251 form Tektronix's family of high-voltage differential probes, sharing a common electrical core — ≤1 pF typical differential input capacitance, 1 MΩ differential input resistance, ±42 V (DC + pk AC) differential input range, 5X/50X attenuation, and ±2% DC gain accuracy — while differing in bandwidth and oscilloscope interface.

All three address the same measurement challenges in switch-mode power supply, CAN/LIN bus, and high-speed digital design, pairing high-speed signal acquisition with versatile device-under-test connectivity and on-scope ease of use.

Each model below is its own dedicated product page with condition-matched pricing. Select the pre-owned listing that matches the bandwidth and oscilloscope interface your bench requires.

The TDP1000 is the 1 GHz model in the family with the TekVPI probe interface, delivering ≤350 ps rise time and supporting selectable bandwidth-limiting filters of 100 Hz, 10 kHz, 1 MHz, and Full. Its differential input offset range is ±42 V at both 5X and 50X attenuation.

Bandwidth is the primary differentiator: the TDP1000 and P6251 are 1 GHz probes with ≤350 ps rise time, while the TDP0500 is a 500 MHz probe with under 700 ps rise time. The TDP1000 and TDP0500 use the TekVPI probe interface; the P6251 uses the TekProbe-BNC Level II interface and connects to TekConnect oscilloscopes through a TCA-BNC adapter.

The models also differ in selectable bandwidth filter limits (100 Hz, 10 kHz, 1 MHz, and Full for the TDP1000 and TDP0500 versus 5 MHz and Full for the P6251) and in differential input offset range (±42 V at 5X or 50X for the TDP1000 and TDP0500, versus ±4.25 V at 5X and ±42 V at 50X for the P6251). See the comparison table for the per-model specifications.

Additional differences in specifications beyond the few shown above are not listed here — see each model's full specifications below.

Accessories Supplied

• Y-lead set (2 each)
• Solder-down lead set, 1 inch (1 each)
• Solder-down lead set, 3 inch (1 each)
• Micro CKT test tip (3 each)
• Tip savers (2 each)
• Longhorn adapters (2 each)
• Straight-pin probe tips (8 each)
• 3-inch ground leads (2 each)
• Color-coding bands (2 each of 5 colors)
• Nylon carrying case (1 each)

Product Core & Specifications

Important: When using MSO/DPO2000/B series oscilloscopes, the TekVPI power supply (Tektronix part number 119-7465-xx) and power cable are required.

Important: Standard warranty: 1 year parts and labor.

Important: For the P6251, the 1103 TEKPROBE power supply may be required to power the probe when used with non-TekProbe interface instrumentation; a TCA-BNC adapter is required to connect to TekConnect oscilloscopes.

About this Pre-Owned unit

This pre-owned unit is inspected and functionally verified in-house before it ships and is backed by our pre-owned warranty. To confirm its exact condition, firmware revision, installed options, or included accessories for your application before ordering, contact our Test Architects.

• Warranty included
• Functional verification included
• Standard Calibration Upgrade Options: No Calibration Required, NIST Traceable, Z540.1 or ISO 17025 with Data, Z540.3 Guardbanding with Data.
• Note that unnecessary accessories may not be included (contact Test Architect to confirm).

ValueTronics supplies both new and used test and measurement equipment. New units ship factory-sealed, exactly as received from the manufacturer; every used unit is inspected and functionally verified in-house at our 20,000 sq ft secure facility in Elgin, Illinois before it ships. Our Test Architects can help you select the condition, calibration, and configuration that fit your application.

Please review the Manufacturer's Data Sheet to verify published specifications. Feedback on this webpage is always welcome — please reach out to your Test Architect at any time for questions or concerns. Thank you, we truly appreciate you being our customer.