Chat Live
Contact Us
sales@valuetronics.com
The Agilent N5264A is a PNA-X measurement receiver that provides five simultaneous receiver inputs and five measurement receivers in a single instrument. It is built around external IF inputs that accept signals from remote mixers or frequency converters, with a selectable IF bandwidth spanning 1 Hz to 5 MHz.
The external IF inputs allow the use of external IF signals from remote mixers or frequency converters, presented as five inputs labeled A, B, C, D, and R on 50 Ohm SMA (female) connectors. The instrument exposes Ethernet, USB, and GPIB host computer interfaces, and its frequency source control interface uses a TTL handshake for coordinating an external source.
ValueTronics International stocks and holds its own inventory in a 20,000 sq ft secure warehouse at 1675 Cambridge Drive in Elgin, Illinois. Every used unit is inspected and functionally verified in-house before it ships, while new units ship factory-sealed exactly as received from the manufacturer.
Hewlett-Packard's test and measurement business was spun out as Agilent Technologies in 1999. Agilent's electronic measurement business was subsequently established as Keysight Technologies in 2014.
| Specification | Value |
|---|---|
| Key Specifications | |
| Measurement Speed (max) points/sec @ 600 KHz IFBW, CW frequency | 400,000 points/sec (Fast CW mode - no point triggering) |
| Receiver Inputs | 5 (simultaneously) |
| Measurement Receivers | 5 (simultaneously) |
| Data Buffer Size | 4 billion bytes |
| Data Buffer size (max. points for single cut) | 500 million points (for single parameter; two parameters are 250 million points each) |
| IF Bandwidth | 1 Hz to 5 MHz |
| Frequency Source Control Interface | TLL hand shake |
| Trigger In / Out | Three pairs |
| Host Computer Interface | Ethernet, USB and GPIB |
| Security | Hard drive removable |
| External IF Inputs | |
| Function | Allows use of external IF signals from remote mixers or frequency converters |
| Connectors | SMA (female); A, B, C, D, R |
| Input Frequency | 7.605634 MHz |
| Input Impedance | 50 Ω |
| RF Damage Level | +23 dBm |
| DC Damage Level | 1 VDC |
| 0.1 dB Compression Point | -9.0 dBm |
| Compression @ -10 dBm, Magnitude | 0.03 dB |
| Compression @ -10 dBm, Phase | 0.23° |
| Noise Floor, 10 Hz IF BW | -143 dBm |
| Noise Floor, 10 KHz IF BW | -113 dBm |
| Crosstalk | -134 dB |
| Dynamic Range @ 10 Hz | 134 dB @ 0.1dB compression to noise floor |
| Dynamic Accuracy (-40 dBm reference, over range set by compression and noise floor @ IF Frequencies) | |
| -10 dBm | 0.037 dB |
| -20 dBm | 0.024 dB |
| -30 dBm | 0.016 dB |
| -40 dBm | 0.010 dB |
| -50 dBm | 0.013 dB |
| -60 dBm | 0.021 dB |
| -70 dBm | 0.032 dB |
| -80 dBm | 0.041 dB |
| -90 dBm | 0.049 dB |
| -100 dBm | 0.057 dB |
| -110 dBm | 0.072 dB |
| -120 dBm | 0.188 dB |
| LO output 2 (Option 108) | |
| Frequency Stability | +/- 0.05 ppm, -10 to 70C, +/- 0.1ppm/yr max |
| Frequency Accuracy | +/- 1 ppm |
| Frequency Range | 10 MHz to 26.5 GHz |
| Frequency Switching Speed | < 100 microsecond/point |
| Frequency Resolution | 1 Hz |
| Power Flatness | +/- 1.0 dB |
| Power Output | +10 dBm |
| 2nd Harmonics, 20 MHz to 2.0 GHz | -23 dBc |
| 2nd Harmonics, 2.0 GHz to 5.0 GHz | -28 dBc |
| 2nd Harmonics, 5.0 GHz to 23.0 GHz | -35 dBc |
| 2nd Harmonics, 23.0 GHz to 26.5 GHz | -27 dBc |
| 3rd Harmonics, 30 MHz to 8.0 GHz | -32 dBc |
| 3rd Harmonics, 8.0 GHz to 15.0 GHz | -38 dBc |
| 3rd Harmonics, 15.0 GHz to 26.5 GHz | -48 dBc |
| Phase Noise, 10 MHz to 500 MHz (1/10/100 kHz, 1 MHz offset) | -80 / -85 / -76 / -113 dBc/Hz |
| Phase Noise, 500 MHz to 1 GHz (1/10/100 kHz, 1 MHz offset) | -90 / -110 / -106 / -115 dBc/Hz |
| Phase Noise, 1 GHz to 2 GHz (1/10/100 kHz, 1 MHz offset) | -85 / -105 / -101 / -110 dBc/Hz |
| Phase Noise, 2 GHz to 4 GHz (1/10/100 kHz, 1 MHz offset) | -80 / -100 / -96 / -105 dBc/Hz |
| Phase Noise, 4 GHz to 8 GHz (1/10/100 kHz, 1 MHz offset) | -74 / -94 / -90 / -99 dBc/Hz |
| Phase Noise, 8 GHz to 16 GHz (1/10/100 kHz, 1 MHz offset) | -68 / -88 / -84 / -93 dBc/Hz |
| Phase Noise, 16 GHz to 26.5 GHz (1/10/100 kHz, 1 MHz offset) | -62 / -82 / -78 / -87 dBc/Hz |
| 10 MHz Reference | |
| Reference In Connector | BNC, female |
| Reference In Input Frequency | 10 MHz ± 10 ppm, typical |
| Reference In Input Level | -15 dBm to +20 dBm, typical |
| Reference In Input Impedance | 200 Ω, nom. |
| Reference Out Connector | BNC, female |
| Reference Out Output Frequency | 10 MHz ± 1 ppm, typical |
| Reference Out Signal Type | Sine Wave, typical |
| Reference Out Output Level | +10 dBm ± 4 dB into 50 Ω |
| Reference Out Output Impedance | 50 Ω, nominal |
| Reference Out Harmonics | <-40 dBc, typical |
| External Monitor Information | |
| VGA Video Output Connector | 15-pin mini D-Sub; Drives VGA compatible monitors |
| Flat Panel (TFT) Resolutions | 1024 X 768, 800 X 600, 640 X 480 |
| Flat Panel (DSTN) Resolutions | 800 X 600, 640 X 480 |
| CRT Monitor Resolutions | 1280 X 1024, 1024 X 768, 800 X 600, 640 X 480 |
| Test Set IO | 25-pin D-Sub connector, available for external test set control |
| Power IO | 9-pin D-Sub, female; analog and digital IO |
| Handler IO | 36-pin parallel I/O port; all input/output signals are default set to negative logic; can be reset to positive logic via GPIB command |
| Trigger Information | |
| Trigger In/Meas Trigger, Nominal Input Impedance | 5K Ohms |
| Trigger In/Meas Trigger, Minimum Pulse Width | 1 us |
| Trigger In/Meas Trigger, DC Damage Level | 5.5 volts |
| Trigger In/Meas Trigger, Drive Voltage | TTL (0, +5.0) Volts |
| Trigger Out/Meas Trigger Ready, Nominal Input Impedance | 5K Ohm |
| Trigger Out/Meas Trigger Ready, Pulse Width | = Data acquisition |
| Trigger Out/Meas Trigger Ready, Polarity | Selectable with sweep or point mode |
| Trigger Out/Meas Trigger Ready, Drive Voltage | TTL (0, +5.0) Volts |
| Trigger Inputs/Outputs (Aux. 1 & 2) | BNC(f), TTL/CMOS compatible |
| GPIB | 24-pin D-sub (Type D-24), female; compatible with IEEE-488 (two ports - dedicated controller and dedicated talker/listener) |
| Parallel Port (LPT1) | 25-pin D-Sub miniature connector, female; provides connection to printers or any other parallel port peripherals |
| Serial Port (COM 1) | 9-pin D-Sub, male; compatible with RS-232 |
| USB Port | Four ports on front panel (all Host) and five ports (four hosts and one Device) on rear panel. Type A configuration (eight hosts) and Type B configuration (one Device), USB 2.0 compatible |
| LAN | 10/100BaseT Ethernet, 8-pin configuration; auto selects between the two data rates |
| Line Power | |
| Frequency, Voltage | 50/60 Hz for 100 240 VAC (auto switching) |
| Max | 450 watts |
Important: External IF input damage levels: +23 dBm RF and 1 VDC.
Important: Simultaneous operation of the internal and external displays is allowed, but with 640 X 480 resolution only. If you change resolution, you can only view the external display (internal display will "white out").
Important: All specifications and characteristics apply over a 25 °C ±5 °C range (unless otherwise stated) and 90 minutes after the instrument has been turned on.
Important: When configuring the N5264A Option 108 as the LO source, you may improve system measurement sensitivity by using a method of AM noise suppression.
Important: For Regulatory and Environmental information, refer to the PNA Series Installation and Quick Start Guide, located online at http://cp.literature.agilent.com/litweb/pdf/E8356-90001.pdf.
This pre-owned unit is inspected and functionally verified in-house before it ships and is backed by our pre-owned warranty. To confirm its exact condition, firmware revision, installed options, or included accessories for your application before ordering, contact our Test Architects.
ValueTronics supplies both new and used test and measurement equipment. New units ship factory-sealed, exactly as received from the manufacturer; every used unit is inspected and functionally verified in-house at our 20,000 sq ft secure facility in Elgin, Illinois before it ships. Our Test Architects can help you select the condition, calibration, and configuration that fit your application.
Please review the Manufacturer's Data Sheet to verify published specifications. Feedback on this webpage is always welcome — please reach out to your Test Architect at any time for questions or concerns. Thank you, we truly appreciate you being our customer.
Model No
Agilent
Condition
Pre-Owned
Manufacturer
Agilent
30+ Years in Business
Secure Payments
Sell Test Equipments
Knowledgeable Staff
On-site Lab
30+ Years in Business
Secure Payments
Sell Test Equipments
Knowledgeable Staff
On-site Lab
Request A Quote
