The HAMEG HM5005 / HM5006 is a spectrum analyzer covering a frequency range of 0.15 MHz to 500 MHz, presented as an instrument for analyzing any kind of signal within that range. Both models include a Scanwidth Selector that adjusts the frequency display width from 50 kHz to 50 MHz per division, and a 4-digit numeric LED readout that selectively displays either the center or the marker frequency. Frequency measurement is performed by positioning a needle-like cursor on the point of interest and reading the 4-digit marker frequency value.

A spectrum analyzer displays signal amplitude as a function of frequency, letting an engineer see the spectral content of a signal — the carrier, harmonics, and spurious products — across a band rather than as a single waveform in time. The HM5005 / HM5006 is positioned for the RF measurement needs of education and industry. On the HM5006, the tracking generator enables a two-port measurement that is useful in network and filter passband analysis.

ValueTronics stocks and holds its own inventory in a 20,000 square-foot secure warehouse at 1675 Cambridge Drive in Elgin, Illinois, so the equipment we list is equipment we keep on hand. Every pre-owned unit benefits from that single-location control: pre-owned units are inspected and functionally verified in-house before they ship, while new units ship factory-sealed exactly as received from the manufacturer.

Brand Heritage

HAMEG Instruments was acquired by Rohde & Schwarz in 2005, after which its product range was progressively integrated under the Rohde & Schwarz brand.

Compare Other Models in This Series

The HM5005 / HM5006 family comprises two spectrum analyzers that share the same 0.15 MHz to 500 MHz frequency range, the same –100 dBm to +13 dBm measurement range, and the same display, attenuator, and resolution-bandwidth architecture. Both include the Scanwidth Selector, the 4-digit center/marker frequency readout, the AM demodulator, earphone output, and 6 V close-field probe power.

The two models are distinguished by a single capability: the HM5006 incorporates a built-in tracking generator, while the HM5005 does not. In every other respect the instruments are specified identically.

Each model below is its own dedicated product page with condition-matched pricing. Select the pre-owned listing that fits your requirement, and compare the model rows in the table that follows to confirm which configuration you need.

The HM5006 is the model that carries the tracking generator — a frequency-synchronous source spanning 0.15 MHz to 500 MHz with an output adjustable from –50 dBm to +1 dBm, a 0 to 40 dB output attenuator, ±1.5 dB flatness, and a 50 Ω BNC female output — enabling the two-port network and filter passband measurements described for this configuration.

The principal difference across the family is the tracking generator, which is present on the HM5006 only. Because it provides a swept source synchronized to the analyzer, the HM5006 supports two-port measurements such as filter passband and network analysis; the HM5005 provides the same receiver-side spectrum analysis without that source.

Both models share frequency range, measurement range, resolution bandwidths, attenuator range, display, and general electrical and mechanical specifications. Refer to the comparison table that follows for the model-by-model breakdown.

Additional differences in specifications beyond the few shown above are not listed here — see each model's full specifications below.

Accessories Supplied

• Line cord
• Operators Manual

Product Core & Specifications

Important: Maximum safe input level: +20 dBm (0.1 W) at 20 dB attenuation, +10 dBm at 0 dB attenuation, and ±25 V DC.

Recommended pairing: add the optional HO500-2 interface to provide a measurement output to a PC for documenting results.

About this Pre-Owned unit

This pre-owned unit is inspected and functionally verified in-house before it ships and is backed by our pre-owned warranty. To confirm its exact condition, firmware revision, installed options, or included accessories for your application before ordering, contact our Test Architects.

• Warranty included
• Functional verification included
• Standard Calibration Upgrade Options: No Calibration Required, NIST Traceable, Z540.1 or ISO 17025 with Data, Z540.3 Guardbanding with Data.
• Note that unnecessary accessories may not be included (contact Test Architect to confirm).

ValueTronics supplies both new and used test and measurement equipment. New units ship factory-sealed, exactly as received from the manufacturer; every used unit is inspected and functionally verified in-house at our 20,000 sq ft secure facility in Elgin, Illinois before it ships. Our Test Architects can help you select the condition, calibration, and configuration that fit your application.

Please review the Manufacturer's Data Sheet to verify published specifications. Feedback on this webpage is always welcome — please reach out to your Test Architect at any time for questions or concerns. Thank you, we truly appreciate you being our customer.