The Agilent ENA-L RF Network Analyzers comprise two models — the E5061A, covering 300 kHz to 1.5 GHz, and the E5062A, covering 300 kHz to 3 GHz. Both are vector network analyzers built on a common platform that employs a graphical user interface based on the Windows operating system, operable through a hardkey interface, an optional touch screen, or a mouse. Each analyzer provides up to four independent measurement channels, each with its own display window and up to four data traces and four memory traces.

A network analyzer characterizes how a device or network reflects and transmits signals across frequency. The ENA-L measures S-parameters — S11 and S21 in the transmission/reflection configuration, and the full S11, S21, S12, and S22 set with the full 2-port option — and converts those parameters into reflection and transmission impedance, reflection and transmission admittance, and 1/S. Available data formats include log and linear magnitude, phase, expanded phase, positive phase, group delay, SWR, real, imaginary, Smith chart, and polar. Fault-location transformation to the distance and time domains is available as an option, alongside limit-line definition for pass/fail testing.

ValueTronics stocks and holds its own test-and-measurement inventory in a 20,000-square-foot secure warehouse at 1675 Cambridge Drive in Elgin, Illinois, and every pre-owned unit is fulfilled directly from that facility. Used units are inspected and functionally verified in-house before they ship, while new units ship factory-sealed exactly as received from the manufacturer.

Brand Heritage

The ENA-L line carries Agilent Technologies branding. Agilent was established in 1999 as a spin-off of Hewlett-Packard, and its electronic test-and-measurement business was subsequently established as Keysight Technologies in 2014.

Compare Other Models in This Series

The ENA-L family is offered as two models sharing a common platform: the E5061A and the E5062A. Both provide the same measurement architecture — up to four channels, Type-N 50 Ω or 75 Ω test ports, the same selectable calibration types, and the same Windows-based interface — and differ primarily in their upper frequency limit.

The E5061A covers 300 kHz to 1.5 GHz, while the E5062A extends coverage to 3 GHz. Measurement-parameter scope (S11/S21 versus the full 2-port S11/S21/S12/S22 set) and capabilities such as fault location, extended power range, and touch screen are selected by option code rather than by base model.

Each model below is its own dedicated product page with pre-owned-matched pricing. Select the model whose frequency range and option configuration matches your measurement requirement, then open the listing for the condition you need.

The principal difference between the two models is frequency span: the E5061A reaches 1.5 GHz and the E5062A reaches 3 GHz, as shown in the comparison table. Test port output frequency range follows the model accordingly — 300 kHz to 1.5 GHz for the E5061A and 300 kHz to 3 GHz for the E5062A.

Beyond frequency range, the two models share corrected-performance specifications, connector options, calibration types, channel count, and interfaces. Measurement-parameter scope and features such as fault location, extended power range, and touch screen are determined by option codes that apply across both models.

Additional differences in specifications beyond the few shown above are not listed here — see each model's full specifications below.

Product Core & Specifications

Important: Maximum test port input level: +10 dBm. Damage level: +20 dBm, ±30 VDC.

Important: A third-wire ground is required for the line power connection.

Important: Level accuracy for 75 Ω analyzers is not a specification for frequencies > 2 GHz; it is a typical characteristic.

Important: System dynamic range specifications apply only to units with serial prefix MY442 and above.

Important: LXI Class C compliance applies only to units shipped with firmware revision A.03.00 or later.

Important: Corrected system performance is achieved using an external calibration kit (85032F for 50 Ω Type-N, 85036E for 75 Ω Type-N); the calibration kit is a separate product and is required to perform full 2-port or enhanced response calibration.

About this Pre-Owned unit

This pre-owned unit is inspected and functionally verified in-house before it ships and is backed by our pre-owned warranty. To confirm its exact condition, firmware revision, installed options, or included accessories for your application before ordering, contact our Test Architects.

• Warranty included.
• Functional verification included.
• Standard Calibration Upgrade Options: No Calibration Required, NIST Traceable, Z540.1 or ISO 17025 with Data, Z540.3 Guardbanding with Data.
• Note that unnecessary accessories may not be included (contact Test Architect to confirm).

ValueTronics supplies both new and used test and measurement equipment. New units ship factory-sealed, exactly as received from the manufacturer; every used unit is inspected and functionally verified in-house at our 20,000 sq ft secure facility in Elgin, Illinois before it ships. Our Test Architects can help you select the condition, calibration, and configuration that fit your application.

Please review the Manufacturer's Data Sheet to verify published specifications. Feedback on this webpage is always welcome — please reach out to your Test Architect at any time for questions or concerns. Thank you, we truly appreciate you being our customer.