The ADP30X high-voltage active differential probes are safe, easy-to-use instruments ideally suited for measuring power electronics. The series comprises the ADP300 and ADP305. The ADP300 is designed for troubleshooting low-frequency power devices and other circuits where the reference potential is elevated from the ground or the location of the ground is unknown, while the ADP305 is designed for measuring the high-speed floating voltages found in today's power electronics.

A high-voltage differential probe measures the voltage difference between two points in a circuit without referencing either point to ground. Within this family, that capability is applied to measuring power electronics, troubleshooting low-frequency power devices, working with circuits whose reference potential is elevated from ground or whose ground location is unknown, and capturing the high-speed floating voltages present in modern power electronics.

ValueTronics stocks and holds its own inventory in a 20,000 square foot secure warehouse at 1675 Cambridge Drive in Elgin, Illinois. Every pre-owned probe is inspected and functionally verified in-house by our technicians before it ships, while new units leave the warehouse factory-sealed exactly as received.

Brand Heritage

LeCroy Corporation was acquired by Teledyne Technologies in 2012 and has since operated under the Teledyne LeCroy name.

Compare Other Models in This Series

The ADP30X high-voltage active differential probes are safe, easy-to-use instruments ideally suited for measuring power electronics. The series includes the ADP300 and ADP305, which differ in bandwidth and intended application while sharing the family's common mode and differential voltage ratings.

Both models are active differential probes built around the ProBus system with full remote control, and both are rated to EN 61010 CAT III with 80 dB CMRR at 50/60 Hz.

Each pre-owned model below is its own dedicated product page with condition-matched pricing. Select the model that matches your bandwidth and application requirement to view its specifications and availability.

The ADP300 provides 20 MHz bandwidth and is designed for troubleshooting low-frequency power devices and other circuits where the reference potential is elevated from the ground or the location of the ground is unknown.

The two models are separated primarily by bandwidth and target application. The ADP300 offers 20 MHz bandwidth for troubleshooting low-frequency power devices, while the ADP305 offers 100 MHz bandwidth for measuring the high-speed floating voltages found in today's power electronics.

Aside from bandwidth and intended use, the models share the family's core ratings: 1,000 V rms common mode voltage, 1,400 V peak differential voltage, 80 dB CMRR at 50/60 Hz, EN 61010 CAT III, and ProBus connectivity with full remote control. See the comparison table that follows for the per-model values.

Additional differences in specifications beyond the few shown above are not listed here — see each model's full specifications below.

Product Core & Specifications

Important: Common mode voltage rating: 1,000 V rms; maximum differential voltage: 1,400 V peak. Rated to EN 61010 CAT III.

Important: The AP031 differential techniques permit measurements between two points in a circuit without reference to ground, allowing the oscilloscope to be safely grounded without opto-isolators or isolating transformers.

About this Pre-Owned unit

This pre-owned unit is inspected and functionally verified in-house before it ships and is backed by our pre-owned warranty. To confirm its exact condition, firmware revision, installed options, or included accessories for your application before ordering, contact our Test Architects.

• Warranty included
• Functional verification included
• Standard Calibration Upgrade Options: No Calibration Required, NIST Traceable, Z540.1 or ISO 17025 with Data, Z540.3 Guardbanding with Data.
• Note that unnecessary accessories may not be included (contact Test Architect to confirm).

ValueTronics supplies both new and used test and measurement equipment. New units ship factory-sealed, exactly as received from the manufacturer; every used unit is inspected and functionally verified in-house at our 20,000 sq ft secure facility in Elgin, Illinois before it ships. Our Test Architects can help you select the condition, calibration, and configuration that fit your application.

Please review the Manufacturer's Data Sheet to verify published specifications. Feedback on this webpage is always welcome — please reach out to your Test Architect at any time for questions or concerns. Thank you, we truly appreciate you being our customer.