Chat Live
Contact Us
sales@valuetronics.com
The Agilent N5230A is a 2-port PNA-L microwave network analyzer. Depending on its installed options, it covers frequencies from 300 kHz to 6 or 13.5 GHz, or from 10 MHz to 20, 40, or 50 GHz, and is offered in both standard test set / standard power range and configurable test set / extended power range configurations.
A network analyzer measures how a device under test transmits and reflects signals across frequency, reporting both magnitude and phase. The N5230A performs full 2-port calibrated measurements of transmission and reflection characteristics, with segment sweep capability that can apply higher power to high-insertion-loss devices and reduced power where receiver compression or damage could occur on low-insertion-loss devices.
ValueTronics stocks and holds its own inventory in a 20,000 square foot secure warehouse at 1675 Cambridge Drive in Elgin, Illinois. Every pre-owned instrument is inspected and functionally verified in-house by our technicians before it ships, while new units ship factory-sealed exactly as received, so buyers can source this analyzer with confidence in either condition.
The instrument carries the Agilent name from the era when Agilent Technologies was spun out of Hewlett-Packard in 1999. Agilent's electronic measurement business was subsequently established as Keysight Technologies in 2014.
| Specification | Value |
|---|---|
| System | |
| Frequency range | Option 020/025: 300 kHz to 6 GHz; Option 120/125: 300 kHz to 13.5 GHz; Option 220/225: 10 MHz to 20 GHz; Option 420/425: 10 MHz to 40 GHz; Option 520/525: 10 MHz to 50 GHz |
| System IF bandwidth range (Option 020, 025, 120, 125) | 1 Hz to 600 kHz, nominal |
| System IF bandwidth range (Option 220, 225, 420, 425, 520, 525) | 1 Hz to 250 kHz, nominal |
| CPU | Intel 1.1 GHz Pentium M with 1 GByte RAM |
| Test Port Output | |
| Nominal power (Option 020, 025) | 0 dBm |
| Nominal power (Option 120, 125) | 0 dBm |
| Nominal power (Option 220, 225) | –5 dBm |
| Nominal power (Option 420, 425) | –10 dBm |
| Nominal power (Option 520, 525) | –15 dBm |
| Frequency resolution | 1 Hz |
| CW accuracy | ±1 ppm |
| Frequency stability | ±0.05 ppm, –10° to 70 °C; ±0.1 ppm/yr maximum |
| Power resolution | 0.01 dB (all options) |
| Minimum power setting (Option 020, 120) | –33 dBm |
| Minimum power setting (Option 025, 125) | –93 dBm |
| Maximum power setting | +20 dBm |
| Front Panel | |
| RF connectors (Option 020, 025, 120, 125, 220, 225) | 3.5 mm (male), 50 ohm, nominal |
| RF connectors (Option 420, 425, 520, 525) | 2.4 mm (male), 50 ohm, nominal |
| Center pin recession | 0.002 in. (characteristic) |
| Display size | 21.3 cm (8.4 in) diagonal color active matrix LCD; 640 (horizontal) X 480 (vertical) resolution |
| Display refresh rate | Vertical 59.83 Hz; Horizontal 31.41 kHz |
| Display range, magnitude | ±500 dB (at 20 dB/div), max |
| Display range, phase | ±500°, max |
| Display resolution, magnitude | 0.001 dB/div, min |
| Display resolution, phase | 0.01°/div, min |
| Marker resolution, magnitude | 0.001 dB, min |
| Marker resolution, phase | 0.01°, min |
| Rear Panel | |
| Trigger inputs/outputs | BNC (f), TTL/CMOS compatible |
| 10 MHz Reference in | BNC female; 10 MHz ± 10 ppm, typical; input level –15 to +20 dBm, typical; input impedance 200 Ω, nom. |
| 10 MHz Reference out | BNC female; 10 MHz ± 1 ppm, typical; sine wave, typical; output level +10 dBm ± 4 dB into 50 Ω, typical; output impedance 50 Ω, nominal; harmonics < –40 dBc, typical |
| VGA video output | 15-pin mini D-Sub; drives VGA compatible monitors |
| Test set IO | 25-pin D-Sub connector, available for external test set control |
| Aux IO | 25-pin D-Sub connector, male, analog and digital I/O |
| Handler IO | 36-pin parallel I/O port; all input/output signals default set to negative logic; can be reset to positive logic via GPIB command |
| GPIB | Two ports: dedicated Controller and dedicated Talker/Listener; 24-pin D-sub (Type D-24), female; compatible with IEEE-488 |
| USB Port | 1 port on front panel and 4 ports on rear panel |
| LAN | 10/100BaseT Ethernet, 8-pin configuration; auto selects between the two data rates |
| Line power (single phase) | 50/60 Hz/400 Hz for 100 to 120 V, 50/60 Hz for 220 to 240 V (power supply is auto switching) |
| Maximum power consumption | 350 Watts |
| Analyzer Environment and Dimensions | |
| EMC | Complies with European EMC directive 89/336/EEC, amended by 93/68/EEC; IEC/EN 61326; CISPR Pub 11 Group 1, class A; AS/NZS CISPR II:2002; ICES/NMB-001 |
| Safety | Complies with European Low Voltage Directive 73/23/EEC, amended by 93/68/EEC; IEC/EN 61010-1:2001; Canada: CSA C22.2 No. 61010-1:2001; USA: UL 61010-1 |
| Operating temperature | 0 to +40 °C |
| Error-corrected temperature range | 23 °C ± 3 °C with less than 1 °C deviation from calibration temp. |
| Relative humidity | Type-tested 0 to 95% at 40 °C, non-condensing |
| Altitude | 0 to 4600 m (15,000 ft.) |
| Non-operating storage temperature | –40 to +70 °C |
| Cabinet dimensions (excluding front and rear panel hardware and feet) | 267 mm (H) x 426 mm (W) x 427 mm (D); 10.5 in x 16.75 in x 16.8 in |
| Net weight | 24.9 kg (55 lb), nominal |
| Shipping weight | 36.3 kg (80 lb), nominal |
Important: Front-panel receiver-access jumpers are present only on the configurable test set / extended power range options (025, 125, 225, 425, 525). The standard test set / standard power range options (020, 120, 220, 420, 520) have no front-panel jumpers.
Important: This is a subset of technical specifications for the N5230A network analyzer; to view or print the complete N5230A technical specifications, visit www.agilent.com/find/pnal.
Important: Corrected (calibrated) system performance applies only when the N5230A is used with a calibration kit (85052B, 85056A, or 85032B) or an electronic calibration (ECal) module (N4691A/N4691B or N4693A), the appropriate flexible test port cable set (85131F, 85133F, or 85132F with 85130C adapter set), and a full 2-port calibration.
Important: Option H08 and Option H11 specifications are not provided in this N5230A specifications document.
This pre-owned unit is inspected and functionally verified in-house before it ships and is backed by our pre-owned warranty. To confirm its exact condition, firmware revision, installed options, or included accessories for your application before ordering, contact our Test Architects.
ValueTronics supplies both new and used test and measurement equipment. New units ship factory-sealed, exactly as received from the manufacturer; every used unit is inspected and functionally verified in-house at our 20,000 sq ft secure facility in Elgin, Illinois before it ships. Our Test Architects can help you select the condition, calibration, and configuration that fit your application.
Please review the Manufacturer's Data Sheet to verify published specifications. Feedback on this webpage is always welcome — please reach out to your Test Architect at any time for questions or concerns. Thank you, we truly appreciate you being our customer.
Model No
Agilent
Condition
Pre-Owned
Manufacturer
Agilent
Net_ana_freq
300 kHz to 50 GHz
240
4-Port Standard Test Set , 300 kHz to 20 GHz
30+ Years in Business
Secure Payments
Sell Test Equipments
Knowledgeable Staff
On-site Lab
30+ Years in Business
Secure Payments
Sell Test Equipments
Knowledgeable Staff
On-site Lab
Request A Quote
