# Agilent N5264A PNA-X Measurement Receiver (Pre-Owned) # Agilent N5264A PNA-X Measurement Receiver (Pre-Owned) ## Key Features At A Glance - Five simultaneous receiver inputs and five measurement receivers - Measurement speed up to 400,000 points/sec at 600 kHz IFBW, CW (Fast CW mode, no point triggering) - Selectable IF bandwidth from 1 Hz to 5 MHz - 4-billion-byte data buffer; up to 500 million points per single cut (single parameter) - Ethernet (LAN), USB, GPIB and RS-232 host interfaces for automated test systems - Removable hard drive for secure environments - Optional internal LO output (Option 108) covering 10 MHz to 26.5 GHz - Five external IF inputs (A, B, C, D, R) on 50 Ohm SMA (female) connectors The Agilent N5264A is a PNA-X measurement receiver that provides five simultaneous receiver inputs and five measurement receivers in a single instrument. It is built around external IF inputs that accept signals from remote mixers or frequency converters, with a selectable IF bandwidth spanning 1 Hz to 5 MHz. The external IF inputs allow the use of external IF signals from remote mixers or frequency converters, presented as five inputs labeled A, B, C, D, and R on 50 Ohm SMA (female) connectors. The instrument exposes Ethernet, USB, and GPIB host computer interfaces, and its frequency source control interface uses a TTL handshake for coordinating an external source. ValueTronics International stocks and holds its own inventory in a 20,000 sq ft secure warehouse at 1675 Cambridge Drive in Elgin, Illinois. Every used unit is inspected and functionally verified in-house before it ships, while new units ship factory-sealed exactly as received from the manufacturer. ## Brand Heritage Hewlett-Packard's test and measurement business was spun out as Agilent Technologies in 1999. Agilent's electronic measurement business was subsequently established as Keysight Technologies in 2014. ## Product Core & Specifications Specification Value Key Specifications Measurement Speed (max) points/sec @ 600 KHz IFBW, CW frequency 400,000 points/sec (Fast CW mode - no point triggering) Receiver Inputs 5 (simultaneously) Measurement Receivers 5 (simultaneously) Data Buffer Size 4 billion bytes Data Buffer size (max. points for single cut) 500 million points (for single parameter; two parameters are 250 million points each) IF Bandwidth 1 Hz to 5 MHz Frequency Source Control Interface TLL hand shake Trigger In / Out Three pairs Host Computer Interface Ethernet, USB and GPIB Security Hard drive removable External IF Inputs Function Allows use of external IF signals from remote mixers or frequency converters Connectors SMA (female); A, B, C, D, R Input Frequency 7.605634 MHz Input Impedance 50 Ω RF Damage Level +23 dBm DC Damage Level 1 VDC 0.1 dB Compression Point \-9.0 dBm Compression @ -10 dBm, Magnitude 0.03 dB Compression @ -10 dBm, Phase 0.23° Noise Floor, 10 Hz IF BW \-143 dBm Noise Floor, 10 KHz IF BW \-113 dBm Crosstalk \-134 dB Dynamic Range @ 10 Hz 134 dB @ 0.1dB compression to noise floor Dynamic Accuracy (-40 dBm reference, over range set by compression and noise floor @ IF Frequencies) \-10 dBm 0.037 dB \-20 dBm 0.024 dB \-30 dBm 0.016 dB \-40 dBm 0.010 dB \-50 dBm 0.013 dB \-60 dBm 0.021 dB \-70 dBm 0.032 dB \-80 dBm 0.041 dB \-90 dBm 0.049 dB \-100 dBm 0.057 dB \-110 dBm 0.072 dB \-120 dBm 0.188 dB LO output 2 (Option 108) Frequency Stability +/- 0.05 ppm, -10 to 70C, +/- 0.1ppm/yr max Frequency Accuracy +/- 1 ppm Frequency Range 10 MHz to 26.5 GHz Frequency Switching Speed < 100 microsecond/point Frequency Resolution 1 Hz Power Flatness +/- 1.0 dB Power Output +10 dBm 2nd Harmonics, 20 MHz to 2.0 GHz \-23 dBc 2nd Harmonics, 2.0 GHz to 5.0 GHz \-28 dBc 2nd Harmonics, 5.0 GHz to 23.0 GHz \-35 dBc 2nd Harmonics, 23.0 GHz to 26.5 GHz \-27 dBc 3rd Harmonics, 30 MHz to 8.0 GHz \-32 dBc 3rd Harmonics, 8.0 GHz to 15.0 GHz \-38 dBc 3rd Harmonics, 15.0 GHz to 26.5 GHz \-48 dBc Phase Noise, 10 MHz to 500 MHz (1/10/100 kHz, 1 MHz offset) \-80 / -85 / -76 / -113 dBc/Hz Phase Noise, 500 MHz to 1 GHz (1/10/100 kHz, 1 MHz offset) \-90 / -110 / -106 / -115 dBc/Hz Phase Noise, 1 GHz to 2 GHz (1/10/100 kHz, 1 MHz offset) \-85 / -105 / -101 / -110 dBc/Hz Phase Noise, 2 GHz to 4 GHz (1/10/100 kHz, 1 MHz offset) \-80 / -100 / -96 / -105 dBc/Hz Phase Noise, 4 GHz to 8 GHz (1/10/100 kHz, 1 MHz offset) \-74 / -94 / -90 / -99 dBc/Hz Phase Noise, 8 GHz to 16 GHz (1/10/100 kHz, 1 MHz offset) \-68 / -88 / -84 / -93 dBc/Hz Phase Noise, 16 GHz to 26.5 GHz (1/10/100 kHz, 1 MHz offset) \-62 / -82 / -78 / -87 dBc/Hz 10 MHz Reference Reference In Connector BNC, female Reference In Input Frequency 10 MHz ± 10 ppm, typical Reference In Input Level \-15 dBm to +20 dBm, typical Reference In Input Impedance 200 Ω, nom. Reference Out Connector BNC, female Reference Out Output Frequency 10 MHz ± 1 ppm, typical Reference Out Signal Type Sine Wave, typical Reference Out Output Level +10 dBm ± 4 dB into 50 Ω Reference Out Output Impedance 50 Ω, nominal Reference Out Harmonics <-40 dBc, typical External Monitor Information VGA Video Output Connector 15-pin mini D-Sub; Drives VGA compatible monitors Flat Panel (TFT) Resolutions 1024 X 768, 800 X 600, 640 X 480 Flat Panel (DSTN) Resolutions 800 X 600, 640 X 480 CRT Monitor Resolutions 1280 X 1024, 1024 X 768, 800 X 600, 640 X 480 Test Set IO 25-pin D-Sub connector, available for external test set control Power IO 9-pin D-Sub, female; analog and digital IO Handler IO 36-pin parallel I/O port; all input/output signals are default set to negative logic; can be reset to positive logic via GPIB command Trigger Information Trigger In/Meas Trigger, Nominal Input Impedance 5K Ohms Trigger In/Meas Trigger, Minimum Pulse Width 1 us Trigger In/Meas Trigger, DC Damage Level 5.5 volts Trigger In/Meas Trigger, Drive Voltage TTL (0, +5.0) Volts Trigger Out/Meas Trigger Ready, Nominal Input Impedance 5K Ohm Trigger Out/Meas Trigger Ready, Pulse Width \= Data acquisition Trigger Out/Meas Trigger Ready, Polarity Selectable with sweep or point mode Trigger Out/Meas Trigger Ready, Drive Voltage TTL (0, +5.0) Volts Trigger Inputs/Outputs (Aux. 1 & 2) BNC(f), TTL/CMOS compatible GPIB 24-pin D-sub (Type D-24), female; compatible with IEEE-488 (two ports - dedicated controller and dedicated talker/listener) Parallel Port (LPT1) 25-pin D-Sub miniature connector, female; provides connection to printers or any other parallel port peripherals Serial Port (COM 1) 9-pin D-Sub, male; compatible with RS-232 USB Port Four ports on front panel (all Host) and five ports (four hosts and one Device) on rear panel. Type A configuration (eight hosts) and Type B configuration (one Device), USB 2.0 compatible LAN 10/100BaseT Ethernet, 8-pin configuration; auto selects between the two data rates Line Power Frequency, Voltage 50/60 Hz for 100 240 VAC (auto switching) Max 450 watts > **Important:** External IF input damage levels: +23 dBm RF and 1 VDC. > **Important:** Simultaneous operation of the internal and external displays is allowed, but with 640 X 480 resolution only. If you change resolution, you can only view the external display (internal display will "white out"). > **Important:** All specifications and characteristics apply over a 25 °C ±5 °C range (unless otherwise stated) and 90 minutes after the instrument has been turned on. > **Important:** When configuring the N5264A Option 108 as the LO source, you may improve system measurement sensitivity by using a method of AM noise suppression. > **Important:** For Regulatory and Environmental information, refer to the PNA Series Installation and Quick Start Guide, located online at http://cp.literature.agilent.com/litweb/pdf/E8356-90001.pdf. ## About this Pre-Owned unit This pre-owned unit is inspected and functionally verified in-house before it ships and is backed by our pre-owned warranty. To confirm its exact condition, firmware revision, installed options, or included accessories for your application before ordering, contact our Test Architects. - Warranty included - Functional verification included - Standard Calibration Upgrade Options: No Calibration Required, NIST Traceable, Z540.1 or ISO 17025 with Data, Z540.3 Guardbanding with Data. - Note that unnecessary accessories may not be included (contact Test Architect to confirm). ValueTronics supplies both new and used test and measurement equipment. New units ship factory-sealed, exactly as received from the manufacturer; every used unit is inspected and functionally verified in-house at our 20,000 sq ft secure facility in Elgin, Illinois before it ships. Our Test Architects can help you select the condition, calibration, and configuration that fit your application. **Please review the Manufacturer's Data Sheet to verify published specifications. Feedback on this webpage is always welcome — please reach out to your Test Architect at any time for questions or concerns. Thank you, we truly appreciate you being our customer.** ## Details - **Price:** 0.0 USD - **Vendor:** Agilent - **Type:** Net Ana - **Tags:** product_manual_group_3 ## Variants | Variant | Price | Available | |---------|-------|-----------| | Default Title | 0.00 USD | In stock | ## Images - Agilent N5264A PNA-X Measurement Receiver (Pre-Owned) --- > Source: [ValueTronics](https://valuetronics.com/products/n5264a-keysight-network-analyzer-used) > Updated: 2026-06-20