# 66204 Chroma Power Meter Used ## Chroma 66204 Digital Power Meter — 4-Channel — Certified PreOwned ### Key Features at a Glance - **Voltage Ranges:** 15 / 30 / 60 / 150 / 300 / 600 Vrms — 1200 Vrms with optional HV kit - **Current Ranges:** 0.005 / 0.02 / 0.05 / 0.2 / 0.5 / 2 / 5 / 20 Arms (CF=4) with dual-shunt design - **Frequency Range:** DC, 15 Hz ~ 10 kHz - **Embedded High-Speed DSP:** 16-bit Analog-to-Digital converters sampling up to 250 kHz - **4-Channel, Half-Rack Form Factor:** capable of supporting full 1P2W / 1P3W / 3P3W / 3P4W wiring configurations, including three-phase four-wire measurements - **Standards Compliance:** Meets ENERGY STAR / EN 50564 / IEC 62301 / ErP / SPEC Power requirements - **Advanced Functions:** Inrush current, V/I THD up to 50 harmonic orders, Energy integration, GO/NG pass-fail criteria - **Remote Interfaces:** USB + GPIB standard, with Control I/O for external trigger **In summary,** the Chroma 66204 is a 4-channel digital power meter that uses 16-bit DSP digitizing technology sampling at 250 kHz to deliver simultaneous voltage, current, real power, reactive power, power factor, frequency, total harmonic distortion (THD), inrush current, and energy measurements across selectable 1P2W, 1P3W, 3P3W, and 3P4W wiring modes. It is built specifically to satisfy ENERGY STAR, EN 50564, IEC 62301, ErP, and SPEC Power measurement methodologies for line-powered products, while still serving as a general-purpose bench and rack power meter for R&D, production, and quality assurance environments. ### What is the Chroma 66204 used for? The Chroma 66204 is used to measure AC and DC power, energy, and harmonic distortion on line-powered products and power-conversion equipment — ranging from low-power consumer electronics drawing only a few milliwatts in standby to three-phase systems pulling tens of amps. Typical day-to-day applications include ENERGY STAR / IEC 62301 standby power verification, switching-mode power supply (SMPS) efficiency testing, the four-channel architecture makes the 66204 particularly well-suited to PV inverter testing: three channels capture three-phase AC output to the grid while the fourth channel captures DC input from the solar array, and inverter efficiency is calculated directly inside the instrument without post-processing. ### How does the 66204 differ from a traditional analog power meter? Traditional analog power meters average instantaneous voltage and current with relatively slow analog circuitry, which produces stable-looking readings on unstable loads but can hide real measurement error. The 66204 replaces that legacy architecture with internal 16-bit A/D converters sampling at up to 250 kHz, then exposes Average Mode, Window Mode, and Integration Mode so the engineer can choose between a snapshot, a real averaged value across a user-defined window (Tw), or true accumulated energy across a user-defined interval (Ti) — the only honest approach for products with hiccup-mode or pulsed-load behavior. **Factual grounding.** The 66204 provides a 5 mA minimum current range with crest factor 4 and 0.1 mW power resolution, supports power measurements across a 75 mW ~ 12 kW power range spanning 48 ranges, and delivers less than 2% uncertainty even for No-Load mode measurements — the regime where most regulatory standby measurements actually live. Voltage accuracy is 0.1% RD + 0.08% RNG from 15 Hz to 1 kHz, and the instrument can capture voltage and current harmonics up to the 50th order with a user-selectable distortion order (n = 2 to 50) for THD calculation per the formula on the datasheet. **Standards alignment.** The 66204 is designed to support the specific measurement methodologies called out by ENERGY STAR, EN 50564, IEC 62301, ErP (the EU Ecodesign / Energy-related Products directive), and SPEC Power. Its built-in 5 kHz low-pass filter mode addresses the 3 kHz bandwidth requirement of ENERGY STAR testing while rejecting the high-frequency switching noise that contaminates SMPS measurements. THD analysis aligns with the 2% / 13th-harmonic ceiling specified in IEC 62301 for the AC supply driving the unit under test, and the Softpanel software (A662008 / A662009) supports IEC 61000-3-2 current harmonics pre-compliance testing on 1P2W single-channel measurements. Engineers commonly compare the Chroma 66204 against the Yokogawa WT series and Hioki PW series. The differentiators that matter in practice: - **Software ecosystem:** The Power Efficiency Softpanel (A662008) integrates the 66204 with Chroma's programmable AC sources and electronic loads to automate full efficiency-curve testing and auto-generate test reports — a single-vendor workflow that is hard to match with a mixed-brand bench. - **Low-power floor:** 5 mA minimum range and 0.1 mW resolution make it directly applicable to USB chargers, IoT devices, and any product where the standby number is the regulatory hurdle. - **PV inverter / EV charger efficiency:** The four-channel 66204 captures DC input and three-phase AC output simultaneously, returning end-to-end inverter efficiency without two-instrument synchronization. - **High-current expansion:** External shunt and CT inputs, plus the A662017 / A662018 Ultra High Precision DCCT (60 A / 200 A) option, extend the platform beyond its 20 Arms direct range into hundreds of amps. ### Orderable Options & Accessories The 66204 ships with the items required to operate the meter on the bench. The following options can be added to the order to extend the platform for high-voltage, high-current, automated, and rack-mount applications: Option P/N Description **A662008** Power Efficiency Test Softpanel **A662009** Softpanel for 66200 Series **A662010** Rack Mount Kit for 1 unit **A662012** 1200V HV option kit **A662013** External CT 50 Arms for Model 66203 / 66204 **A662014** External CT 100 Arms for Model 66203 / 66204 **A662015** Voltage and current measurement cables for Model 66204 _(recommended for this model)_ **A662017** Ultra High Precision DCCT 60 A **A662018** Ultra High Precision DCCT 200 A **A662019** DCCT Power Adapter for single channel **A662020** DCCT Power Adapter for multi-channels ### Inside the 66204 — DSP Architecture, Wiring Modes & Measurement Engine The 66200 series replaces traditional analog signal-conditioning chains with a fully digital signal-path: voltage and current are conditioned at the input, then handed directly to internal 16-bit A/D converters sampling at up to 250 kHz, then processed by an embedded DSP. This is what enables simultaneous Vrms, Vpk, Irms, Ipk, inrush current (Is), real power (W), apparent power (VA), reactive power (VAR), power factor (PF), current crest factor (CFi), frequency (F), voltage THD, current THD, and accumulated energy (E) — all from the same acquisition, on the same display, on the same time-base. Each of the 4 channels can act independently, which is what makes the multi-channel architecture useful in practice. Channels can be assigned together into one of four wiring presets, depending on whether the engineer is measuring a single-phase product or a three-phase system: Wiring Mode Channel 1 Channel 2 Channel 3 Channel 4 1P2W (Single Phase Two Wire) 1P2W 1P2W 1P2W 1P2W 1P3W (Single Phase Three Wire) 1P3W 1P2W 1P2W 3P3W (Three Phase Three Wire – Two Wattmeter Method) 3P3W 1P2W 1P2W 3P4W (Three Phase Four Wire) 3P4W 1P2W ### Average, Window & Integration Modes — Real Answers on Unstable Loads Most line-powered products do not present a stable load. SMPS designs cycle in and out of burst / hiccup modes; standby controllers wake and sleep; motor drives draw inrush at start-up. A traditional average reading collected over an arbitrary aperture can look stable yet be wrong by several percent. The 66204 provides three deliberate ways to handle this: - **Average Mode:** Conventional averaging over a single short aperture (T1, T2, T3, T4). - **Window Mode (Tw):** Aggregates all data across a user-defined time window — yields a true average without data loss. - **Integration Mode (Ti):** Calculates active power by integrating V × I across a user-defined interval — the accumulated-energy approach that produces transient-free readings. For low-power measurements below 10 W, the 0.1 mW resolution, 5 mA minimum current range with crest factor 4, and less than 2% No-Load uncertainty make the 66204 a credible choice for ENERGY STAR, IEC 62301, ErP, and SPEC Power testing. ### Inrush Current, Low-Pass Filter & THD Analysis Built-in inrush current (Is) measurement captures the peak current at power-up, with a user-settable trigger level and an optional Delay parameter to bypass the initial peak caused by the input X-capacitor. An external TTL signal can trigger inrush measurement via the rear-panel Control I/O — useful for production-line automation. The instrument's native measurement bandwidth is 50 kHz. A switchable low-pass filter reduces this to 5 kHz, which rejects SMPS switching noise while still meeting the 3 kHz requirement of ENERGY STAR. THD analysis is provided for both voltage and current; the user can additionally specify a distortion order n (n = 2 to 50) to compute partial THD per the standard formula displayed on the datasheet. ### GO/NG Pass-Fail & Multi-Channel Efficiency User-defined upper and lower limits on each parameter drive a front-panel PASS / FAIL indicator (green / red) — the foundation of production-line and incoming-inspection workflows. With wiring mode set to 1P2W, the 66204 can perform up to four simultaneous independent power measurements on four units under test, suitable for production-line throughput. ### Softpanel Software & Automation The 66200 Softpanel (A662009) provides a graphical interface to control and read the meter via USB or GPIB, observe live voltage / current waveforms, log selected parameters to file, and run IEC 61000-3-2 current harmonics pre-compliance tests. The Power Efficiency Test Softpanel (A662008) extends this into automated efficiency sweeps when combined with Chroma's programmable AC sources and electronic loads, including an auto-generated test report at the end of the run. _(IEC 61000-3-2 pre-compliance and the Power Efficiency Softpanel are supported by 1P2W single-channel measurements only.)_ ### Complete Specifications Chroma 66204 — Digital Power Meter (4 channels) — Specifications General **Channel** 4 **Parameters** V, Vpk, I, Ipk, Is, W, VA, VAR, PF, CFi, F, THD V, THD I, E AC/DC Voltage **Range** 15V / 30V / 60V / 150V / 300V / 600 Vrms (CF=2), 6 ranges. HV option up to 1200 Vrms. **Accuracy** 15Hz to 1kHz: 0.1% RD + 0.08% RNG 1kHz to 10kHz: (0.1 + 0.05 × kHz)% RD + 0.05% RNG **Harmonics Accuracy** 15Hz to 1kHz: 0.1% RD + 0.08% RNG 1kHz to 10kHz: (0.1 + 0.05 × kHz)% RD + 0.05% RNG **Input Resistance** 2 MΩ AC/DC Current **Range \*1** 5mA / 20mA / 50mA / 200mA / 500mA / 2A / 5A / 20 Arms (CF=4) **Accuracy** DC, 15Hz to 1kHz: 0.1% RD + 0.12% RNG 1kHz to 10kHz: (0.1 + 0.05 × kHz)% RD + 0.1% RNG **Harmonics Accuracy** 15Hz to 1kHz: 0.1% RD + 0.12% RNG 1kHz to 10kHz: (0.1 + 0.05 × kHz)% RD + 0.1% RNG **DC Current Accuracy** 0.1% RD + 0.1% RNG Power **Range** 75 mW ~ 12 kW (48 ranges) **Accuracy** 47Hz to 63Hz: 0.1% RD + 0.1% RNG 1kHz to 10kHz: (0.1 + 0.1 × kHz + 0.3 / PF × kHz)% RD + 0.18% RNG **Power Factor Accuracy** 0.001 + (15ppm/PF) × Hz Frequency **Range** DC, 15 Hz ~ 10 kHz **Measuring Condition** Voltage (10 ~ 100% of the voltage range) Other **Display Resolution** 5 Digits **Display Update Rate** 0.25 sec / 0.5 sec / 1 sec / 2 sec **Input Voltage** 100 ~ 240V ±10%, 50/60 Hz **Interface** USB + GPIB (Standard) **Operation Temperature** 0 °C ~ 40 °C **Storage Temperature** \-40 °C ~ 85 °C **Safety & EMC** CE (includes EMC & LVD) **Dimensions (H × W × D)** 133 × 212 × 420 mm / 5.25 × 8.25 × 16.3 inch **Weight** 8.5 kg / 18.7 lbs _Note \*1: Power ranges are based on multiplication of different combinations of current and voltage ranges. Specifications are valid only after the power meter has been turned on for more than one hour in a thermally stable environment._ ### Front- & Rear-Panel Connectivity - **Front panel:** Parameter selection, channel selection, system setting / function indicators, system configuration, voltage range selection, current range selection, power ON/OFF, wiring mode selection. - **Rear panel:** GPIB remote interface, USB remote interface, Control I/O signals, voltage measurement inputs, AC input power, external shunt input, current measurement inputs. _Note: Upon discontinuance, ValueTronics will work to supply this product as a Used Certified PreOwned unit if it is required to support existing customer workflows._ ### About This PreOwned Unit This Chroma is offered as a **Certified PreOwned** instrument. The factory-new configuration has reached end of new manufacture, but ValueTronics continues to source, verify, and supply these meters so that customers can maintain existing factory lines, respect existing capital budgets, and standardize on a known measurement platform. - **Warranty:** Every PreOwned 66200-series meter ships with a ValueTronics performance warranty. - **Verification:** Each unit is performance-verified by our technicians prior to shipment. - **Calibration:** NIST-traceable calibration is available as an optional add-on for quality-system, ISO 9001, AS9100, and FDA-regulated environments. - **Accessories:** Unnecessary accessories may not be included. Items shipped are determined on a case-by-case basis to match the workflow you describe. If you have a specific configuration, wiring mode, or accessory dependency in mind (1P2W / 1P3W / 3P3W / 3P4W, HV option, DCCT, rack mount), contact us before ordering — we will confirm fitment and availability for your application. ## Details - **Price:** 0.0 USD - **Vendor:** Chroma - **Type:** Pow Met ## Variants | Variant | Price | Available | |---------|-------|-----------| | Default Title | 0.00 USD | In stock | ## Images - 66204 Chroma Power Meter Used --- > Source: [ValueTronics](https://valuetronics.com/products/66204-chroma-power-meter-used) > Updated: 2026-05-21